| 01. |
General
Requirements |
14% |
| |
0101. Permits Required
Determine when permits are required and issue
permits.
|
1% |
|
| |
0102. Piping Protection
Inspect all piping systems to insure protection
as required from corrosion, stress and strain,
freezing, and physical damage.
|
3% |
|
| |
0103. Piping Installation, Support, Sleeving
and Penetrations
Inspect all piping systems for proper installation,
support, sleeving, penetrations and waterproofing
of exterior openings.
|
4% |
|
| |
0104. Damage to Structural Elements
Inspect building components for damage due to
installation of the plumbing systems.
|
3% |
|
| |
0105. Required Test of Plumbing Systems
Verify that all required tests of installed piping
systems are conducted.
|
3% |
|
| 02. |
Fixtures
|
8% |
| |
0201. Maximum Required
Inspect for proper location and the minimum required
fixtures.
|
1% |
|
| |
0202. Fixture and Material Approvals
Inspect for approved materials and fixture approvals.
|
1% |
|
| |
0203. Installation, Location, Clearance and
Access
Inspect for proper installation of fixtures, waste
receptors, appliances and appurtenances including
clearances, access and sealing.
|
3% |
|
| |
0204. Flow Rates
Inspect for maximum and minimum flow rates and
temperature control valves.
|
2% |
|
| |
0205. Faucets, Fittings and Accessories
Inspect for proper installation of faucets, fixture
fittings and accessories.
|
1% |
|
| 03. |
Water
Heaters |
12% |
| |
0301. Uses, Installation and Labeling
Inspect for proper use and installation of materials
and check for appliance approval.
|
2% |
|
| |
0302. Clearance, Location, Protection, Pans,
Seismic Restraint
Inspect for clearances, locations, protection,
pans and seismic restraint.
|
3% |
|
| |
0303. Valves and Expansion Tanks
Inspect for required valving, T&P valve and
discharge piping installation, thermal expansion
requirements and pipe sizing.
|
4% |
|
| |
0304. Combustion Air and Gas Piping
Inspect for proper sizing of fuel gas piping,
combustion air requirements and required venting.
|
3% |
|
| 04. |
Water
Supply and Distribution |
21% |
| |
0401. Materials, Joints and Connections
Inspect for approved materials, joints and connections.
|
3% |
|
| |
0402. Identification, Sizing and Valving
Inspect the service and distribution piping for
proper installation of cold and hot water delivery,
identification, sizing and valving.
|
7% |
|
| |
0403. Protection Against Contamination
Inspect the potable water supply and distribution
piping for proper protection against contamination.
|
6% |
|
| |
0404. Pressure and Volume Requirements
Verify the minimum and maximum pressure and volume
requirements.
|
3% |
|
| |
0405. Potable Water and Treatment
Verify the requirements for potable water and
installation of water treatment.
|
2% |
|
| 05. |
Sanitary
Drainage |
23% |
| |
0501. Materials and Fittings
Inspect for approved materials and use of proper
fittings, joints, and connections.
|
4% |
|
| |
0502. Sizing of System
Inspect for proper sizing and installation of
the building drain, building sewer, branches and
stacks.
|
8% |
|
| |
0503. Valves, Sumps, Ejectors, and Cleanouts
Inspect for the proper installation of backwater
valves, sumps, ejectors and required cleanouts.
|
3% |
|
| |
0504. Traps
Inspect for the correct type, size, design, location
and installation of traps.
|
5% |
|
| |
0505. Indirect Waste
Inspect indirect waste systems for air breaks
or air gaps.
|
3% |
|
| 06. |
Vents
|
22% |
| |
0601. Material, Joints, Connection and Grade
Inspect for approved materials, joints, connections
and proper grades.
|
5% |
|
| |
0602. Sizing
Inspect for the proper sizing of the venting system.
|
6% |
|
| |
0603. Methods and Installation
Inspect for the minimum venting requirements,
methods and installation.
|
11% |
|
